Search results for: 'for fitting'

Pull-cord release and resetting device to fit on door handle. L = 3 m

Automatic barrier with reversible brushless gear motor; painted aluminum wardrobe with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Automatic barrier with irreversible brushless gear motor; galvanized and painted steel cabinet with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Automatic barrier with 24 V DC operator with encoder; galvanised steel and painted cabinet with set up for fitting accessories. Balancing spring included.

CAME Connect	European Standards

Automatic barrier with 24 V DC operator with encoder; galvanised steel and painted cabinet with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Support for fitting DIR-series photocells.

DOC-E Surface fitting safety photocells 20m range ~ Replaced With The DLX30CEP

DLX30CEP - Direct Replacement

DOC-I Flush fitting safety or free exit photocells 20m range. ~ Replaced With The DLX30CIP

DLX30CIP - Direct Replacement

G4000 are issued with the arm clamp for a rectangular arm. This G0405 is required for fitting a 60mm diameter tubular arm.

G6000 are issued with the arm clamp for a rectangular arm. This G0605 is required for fitting a 100mm diameter tubular arm.

The VD961A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

The VD963A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

RIY077 is a tri-lobe manual release key. It is used to open most Came sliding gate motor manual release covers. Once inside the sliding gate release compartment, there is a yellow knob to turn.  It also fits the manual release mechanism on Came FROG underground motor systems fitted with the A4365 release. These keys are sold singly, or in a box of ten. 

Barrier arm for G4000 cabinets, white 60mm diameter. Fits the G0405 arm clamp. The G0461 reflective strips are recommended.

Barrier arm for G6000 cabinets, white 100mm diameter. This arm fits the G0605 arm clamp. The G0461 reflective strips are recommended.

Semi-oval section barrier arm in white aluminum alloy.  A yellow rubber bump strip is fitted in a groove under the arm. Arm length is 4m for 3.75m opening.

119RIA047 is the manual release handle used on Came underground gate systems that have the A4364 fitted. This is the low security release mechanism. The release handle can be inserted at the base of the gate from either side of the gate. When inserted, turn the handle by about 120 degrees. When unlocked, the gate is disengaged from the underground drive.

FTL-P   Complete kit for a pair of swing gates weighing up to 200 kg per leaf / max width 2 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

Reads cards and tags on Manchester protocol, such as Came TST01, TAG, or PCT. The selector sends the data to a control panel or card processor. Both processing device will need a R700 card to comunicate with the reader. The selector does not store any data, so data cannot be stollen with the reader, the reader can be changed without loosing data, and the gate cannot be activated from the wires to the reader.

There is a blue backlight behind the sensitive area. 

Flush mount SEL options can be fitted in the CSS or CSSN posts.

Click here to view SELR1BDG manual

Complete kit for a sliding gate weighing up to 1500 kg / max width 20 m

CAME Connect	European Standards